Difference between revisions of "Hairpin formation"

From OxDNA
Line 62: Line 62:
<h5>Figure 1: Probability of having a hydrogen-bonding interaction energy <math>U_{HB}</math> for the SA model. Inset: time series of the hydrogen-bonding energy (stored in the fifth column of the energy file as a function of MD steps.</h5>
<h5>Figure 1: Probability of having a hydrogen-bonding interaction energy <math>U_{HB}</math> for the SA model. Inset: time series of the hydrogen-bonding energy.</h5>

Revision as of 18:13, 21 April 2012


In this example, you will simulate a single strand of length 18 and sequence GCGTTGCTTCTCCAACGC at 334 K (~61 °C) in three different ways:

  • with a molecular dynamics (MD) simulation of the sequence-averaged (SA) model. The input file is inputMD.
  • with an MD simulation of the sequence-dependent (SD) model. The input file is inputMD_seq_dep.
  • with a Monte Carlo (MC) simulation of the SA model in which two base pairs are connected by mutual traps (i.e. additional attractive interactions between two nucleotides). The input file is inputTRAP.

The traps act between the pairs depicted in blue and red in the sequence GCGTTGCTTCTCCAACGC. The details of the interaction associated to the traps can be changed in the file hairpin_forces.dat.

This strand, if T is sufficiently low, tends to form an hairpin with a 6-base long stem and a 6-base long loop. The temperature has been chosen to be close to the melting temperature of such a hairpin in the SA version of the model

This document explains how to prepare the hairpin example (see Preparation) and how to run it (Running). Section Results contains results and plots extracted from the simulation output. In the following, $EXEC refers to the oxDNA executable.


The script run.sh generates the input files and runs all the three simulations, one after the other. With the default input files, each simulation, lasting steps by default, takes approximately one hour on a modern CPU. The default run.sh expects $EXEC to be in the ../.. directory. If this is not the case, open run.sh and change the variable CODEDIR accordingly.

If you only want to generate the initial configuration, you can issue ./run.sh --generate-only. Then you can run the simulations by yourself. The generated initial configuration files are initial.top (which contains the topology) and initial.conf (which contains positions and orientations of the nucleotides).


In order to run the whole example, it is sufficient to issue the command ./run.sh (or bash run.sh). As described in Preparation, you can generate the initial configuration and then run the simulations by hand. The three simulations, described in Introduction, can be performed issuing $EXEC input, where input is a text file that specifies the simulation configuration. For this example, three files have been prepared: inputMD, inputMD_seq_dep and inputTRAP. The table below reports all the files associated to each simulations.

Type Input energy file trajectory file last configuration file log file
SA model inputMD energy.dat trajectory.dat last_conf.dat log.dat
SD model inputMD_seq_dep energy_seq_dep.dat trajectory_seq_dep.dat last_conf_seq_dep.dat log_seq_dep.dat
SA model with traps inputTRAP energy_trap.dat trajectory_trap.dat last_conf_trap.dat log_trap.dat


As mentioned in the Introduction, temperature has been chosen so that the hairpin is near its melting temperature when simulated via SA model. Figure 1 shows the probability distribution histogram for the hydrogen-bonding (HB) energy of the system (in simulation units. Both the minimum in and a direct inspection of the time series (inset) show that the hairpin is indeed near the melting temperature, since oscillates between 0 (no HBs) and ~ -3.5, which corresponds to 4-5 hydrogen-bonded nucleotides. At this temperature the fraying effect is relevant, and therefore the last base-pair is not always formed. This is clearly visible in the snapshot at the beginning of this document, in which 4 base-pairs are formed.


Figure 1: Probability of having a hydrogen-bonding interaction energy for the SA model. Inset: time series of the hydrogen-bonding energy.

Figure 2 shows and for the SD hairpin. In this case, one expects a different melting temperature. Indeed, at this temperature the hairpin is nearly always in its folded conformation and the average value of is lower than in the SA case. Although stacking interactions play a role, the major contribution to this effect is due to the presence of four GC only two AT base-pairs in the stem.


Figure 2: Same as Figure 1, but for the SD model.

If mutual traps between stem base-pairs are introduced, then the equilibrium properties of the hairpin are changed and, even if the SA model is employed, the hairpin is always (after the initial equilibration) in its folded conformation. The use of mutual traps can highly decrease the simulation time required by the folding of strands into target structures (like DNA origami or DNA constructs).


Figure 3: Same as Figure 1, but for the system with mutual traps. Time is expressed in Monte Carlo sweeps.